The 15mm high garage door floor seal kit has been designed to form a watertight seal between the garage door and the floor against standing water up to 15mm high. The threshold will also prevent leaves, dust and debris from being blown under the garage door, thus ensuring a clean and dry environment.
As well as weatherproofing your garage door, our 15mm garage door floor seal can also prevent mice and other small rodents from squeezing underneath the gap between the door and the floor. The yellow line provides a highly visible warning for people or vehicles passing over the threshold.
This threshold seal is 15mm high, 85mm wide, and is available in lengths from 2.21m (7'3") to 20m (65') to suit all sizes of garage door.
The door threshold pushes up against the back of your garage door. It is supplied with a specially formulated adhesive & sealant which provides a water-tight seal between the threshold and the floor, preventing standing water up to 15mm high and rainwater from being blown under your door.
The garage door seals can be used on all types of domestic doors, including up-and-over, sectional, roller shutter, and side-hinged doors. The threshold can be safely driven over with most vehicles.
This threshold seal has a weight limit of 2722 kg making it suitable for most cars and domestic garages. It is not suitable for forklift trucks, vans, lorries, tractors etc., or high traffic areas like parking garages.
This product is not suitable for use on loose concrete or gravel surfaces. Unsealed concrete floors that have a dusty or powdery surface must be sealed with a concrete sealer prior to installation.
The threshold can be installed on epoxy floors, but if the surface is very smooth it can prevent the adhesive from bonding properly. If your epoxy floor has a smooth or shiny surface, a low-grit sandpaper can be used to dull the surface slightly before installation. The same can be done for very smooth tiles. Remove any dust and debris left behind before proceeding to installation.
Due to coiling in transport, the threshold seal should be laid flat on a clean surface so that it returns to its original shape. The adhesive / sealant should be stored at room temperature prior to application so it can flow freely from the tube. The recommended ambient temperature for applying the adhesive is 5°C to 35°C (40°F to 95°F).
Once fitted allow 24 hours before driving over the threshold. It is also recommended to test the installation after 24 hours using a bucket of water or a hosepipe to check for water ingress.
£31.99
The 20mm high garage door floor seal kit has been designed to form a watertight seal between the garage door and the floor against standing water up to 20mm high. The threshold will also prevent leaves, dust and debris from being blown under the garage door, thus ensuring a clean and dry environment.
As well as weatherproofing your garage door, our 20mm garage door floor seal can also prevent mice and other small rodents from squeezing underneath the gap between the door and the floor. The yellow line provides a highly visible warning for people or vehicles passing over the threshold.
This threshold seal is 20mm high, 110mm wide, and is available in lengths from 2.21m (7'3") to 20m (65') to suit all sizes of garage door.
The door threshold pushes up against the back of your garage door. It is supplied with a specially formulated adhesive & sealant which provides a water-tight seal between the threshold and the floor, preventing standing water up to 20mm high and rainwater from being blown under your door.
The garage door seals can be used on all types of domestic doors, including up-and-over, sectional, roller shutter, and side-hinged doors. The threshold can be safely driven over with most vehicles.
This threshold seal has a weight limit of 2722 kg making it suitable for most cars and domestic garages. It is not suitable for forklift trucks, vans, lorries, tractors etc., or high traffic areas like parking garages.
This product is not suitable for use on loose concrete or gravel surfaces. Unsealed concrete floors that have a dusty or powdery surface must be sealed with a concrete sealer prior to installation.
The threshold can be installed on epoxy floors, but if the surface is very smooth it can prevent the adhesive from bonding properly. If your epoxy floor has a smooth or shiny surface, a low-grit sandpaper can be used to dull the surface slightly before installation. The same can be done for very smooth tiles. Remove any dust and debris left behind before proceeding to installation.
Due to coiling in transport, the threshold seal should be laid flat on a clean surface so that it returns to its original shape. The adhesive / sealant should be stored at room temperature prior to application so it can flow freely from the tube. The recommended ambient temperature for applying the adhesive is 5°C to 35°C (40°F to 95°F).
Once fitted allow 24 hours before driving over the threshold. It is also recommended to test the installation after 24 hours using a bucket of water or a hosepipe to check for water ingress.
£44.99
Speak to one of our specialist advisors for more information about this product.